IC693MDL241

GE-IP | 9030 | GE Fanuc 90-30 GE-IP PLC

IC693MDL241 Image

IC693MDL241

Same Day - Free Shipping

  • Manufacturer: GE-IP
  • Description: 24 Volts ac/Vdc Input
  • Weight: 1 lbs :: ≈ 1 kgs
  • Warranty: 1 Years
  • Product Revisions Available:
  • Other Available Revisions of the IC693MDL241 : A, B, C, D, E, F, G, H, I, J, K, L, M, N, O, P, Q, R, S, T, U, V, W, X, Y, Z,

Product Manual Excerpt

24 Volt AC/DC Positive/Negative Logic Input, 16 Point IC693MDL241 The 24 volt AC/DC Positive/Negative Input module for the Series 90-30 Programmable Logic Controller provides 16 input points in one group with a common power input terminal. This input module is designed to have either positive or negative logic characteristics in the DC input mode. This input module is designed to function with AC or DC user inputs. Input characteristics are compatible with a wide range of user-supplied input devices, such as pushbuttons, limit switches, and electronic proximity switches. Current into an input point results in a logic 1 in the input status table (%I). Power to operate the field devices can be supplied by the user, or the Isolated +24 VDC output on the power supply (bottom two power supply terminals) can be used to power a limited number of DC inputs. LED indicators which provide the ON/OFF status of each point are located at the top of the module. This LED block has two horizontal rows with eight green LEDs in each row; the top row labeled A1 through 8 (points 1 through 8) and the bottom row labeled B1 through 8 (points 9 through 16). An insert goes between the inside and outside surface of the hinged door. The surface towards the inside of the module (when the hinged door is closed) has circuit wiring information, and circuit identification information can be recorded on the outside surface. The outside left edge of the insert is color-coded blue to indicate a low-voltage module. This module can be installed in any I/O slot of a 5 or 10-slot baseplate in a Series 90-30 PLC system. Table 6-4. Specifications for IC693MDL241 Rated Voltage 24 volts AC or 24 volts DC Input Voltage Range 0 to +30 volts DC or 0 to +30 volts AC, 50/60 Hz Inputs per Module 16 (one group with a single common) Isolation 1500 volts between field side and logic side Input Current 7 mA (typical) at rated voltage Input Characteristics On-state Voltage 11.5 to 30 volts AC or DC Off-state Voltage 0 to +4 volts AC or DC On-state Current 3.2 mA minimum Off-state Current 1 mA maximum On response Time 12 ms typical Off response Time 28 ms typical Power Consumption: 5V 80 mA (all inputs on) from 5 volt bus on backplane Power Consumption: 24V 125 mA from the Isolated 24 volt backplane bus or from user supplied power Number of inputs on is dependent upon ambient temperature as shown in figure 6 9. Refer to Appendix B for product standards and general specifications. 6 6-8 Series 90-30 PLC I/O Module Specifications July 2000 GFK-0898F IC693MDL241 Input Module Field Wiring Information The following figure provides wiring information for connecting user supplied input devices and power source to the 24 volt AC/DC positive/negative logic input module.

Need To Order A Specific Revision?

Give us a call at 1-800-360-6802 or 1-919-535-3180. We can help you with your Revision specific needs.


UPS Ground shipping is always FREE!


What is New Surplus?

These “New Surplus” units are a great cost saving alternative. This product is in the original manufacturer’s packaging with all sub-assemblies and documentation. Comes with a PLC Distribution Factory & Supply 3-year warranty.


UPS Ground shipping is always FREE!


What is Surplus New?

Surplus New - New unused and includes all sub-assemblies and documentation. Product may ship in manufacturer or PLC Distribution Factory & Supply packaging and includes a PLC Distribution Factory & Supply 3 Year Warranty.


UPS Ground shipping is always FREE!


What is Reconditioned?

Reconditioned products from PLC Distribution Factory & Supply are a cost-effective alternative to new and obsoleted PLC products. Every part is reconditioned down to the circuit board level. All parts are thoroughly inspected and hand-cleaned before being functionally tested in a fully configured system.


Our Reconditioned Products always come with a PLC Distribution Factory & Supply 2-Year Warranty.

UPS Ground shipping is always FREE!


110% PRICE MATCH GUARANTEE


We stand behind our prices with a 110% price match guarantee. If you buy a part from us and, within seven days of purchase, find that part advertised on an authorized distributor's website for less, simply contact us and give us a link to the lower advertised price and we'll refund you 110% of the difference between your purchase price and the advertised lower price. The part must be in-stock for immediate shipment and be in similar condition. All pricing must be displayed without signing in.

Repair Service


3-5 Days for most repairs. 24 hour repair upon request at no extra charge. If part is unrepairable, we will exchange with a working unit or return unrepaired.