IC693CPU363 | IC693CPU363-BG

GE-IP | 9030 | GE Fanuc 90-30 GE-IP PLC

product-image

IC693CPU363 | IC693CPU363-BG

  • Availability: In StockShips Today!
  • Units in Stock: Immediate Availablity: 6 Units!
  • Call for best Pricing+ 1 919 680 1773
  • Manufacturer: GE-IP
  • Description: GE Fanuc Series 90-30 CPU Module with serial ports
  • Weight: 1 lbs :: ≈ 1 kgs
  • Warranty: 1 Years
  • Product Revisions Available:
  • Other Available Revisions of the IC693CPU363 : -AB, -AC, -AD, -BD, -BE, -BF, -BG, -BH, -CJ, -DJ, -DK,

Product Manual Excerpt

December 4, 2002 GFK-2241 IMPORTANT PRODUCT INFORMATION READ THIS INFORMATION FIRST Product: IC693 CPU Module with Firmware Release 10.70 IC693CPU363-BG Introduction This document contains information that is not available in any other publication; therefore, we recommend you save it for future reference. This firmware release adds the Modbus® RTU Master feature to serial ports 1 and 2 of the IC693CPU363. (For details, see “New Features” on page 3.) Modbus RTU Master is not supported on the IC693CPU363 power supply port. The CPU363 is the only IC693 CPU model included in this release. Hardware Identification The following table shows the revision level of the circuit boards used in the current version of these CPUs. CPU Catalog Number Circuit Board ID Circuit Board Version IC693CPU363-BG CX3A1 44A739579-G01R05 or later Firmware Upgrade Kits If you wish to upgrade an existing CPU363 to firmware version 10.70, you may purchase the applicable kit identified in the following table. All previous versions are capable of being upgraded. Firmware Upgrade Kit Catalog Numbers CPU Catalog Number Firmware Upgrade Kit Catalog Numbers IC693CPU363-BG 44A747766-G06 Firmware Identification CPU Catalog Number Flash location CPU Firmware Daughterboard Firmware IC693CPU363-BG On board CX3A1: U2 and U3 On board ES3A1: U10 Main: R10.70 (29A1) Boot: R9.00 (33A1) Main: R10.10 (46A1) Boot: R2.00 (30A1) Functional Compatibility IC693 PLCs can be configured and programmed with any of the following PLC programming products: CIMPLICITY Machine Edition Logic Developer – PLC, VersaPro, Control, or Logicmaster 90-30. • The following or newer versions are required to use C programming or SFC subroutines: CIMPLICITY Machine Edition Logic Developer – PLC software version 2.11 VersaPro software version 1.11 Control software version 2.00 or later. • C toolkit version 4.00 or later must be used for C programming. • Logicmaster software compatibility: Version 9.01 or later is required to configure a CPU363. Version 9.02 or later is required to use features in CPU363 firmware release 9.00 or later. 2 Important Product Information GFK-2241 Operating Notes User Information is Cleared when Upgrading Firmware User information, consisting of program, configuration, CPU ID (used for SNP communications), and status tables in RAM memory, will automatically be cleared if the CPU firmware in flash memory is changed. You will need to restore these if upgrading firmware. A recommended procedure is to first back up your user information from RAM memory to Flash memory. Then write your new firmware to Flash memory (firmware is stored in a different location in Flash memory than that used for storing user information such as program, configuration, etc.). Finally, write your user information back out of Flash into RAM memory. As an alternative, your user information (program, configuration, etc.) can be restored from a computer-based backup program folder using your PLC programming software. The SNP ID, if required, must be set separately using the programming software or the Hand-Held Programmer (HHP). The overrides may be restored from the programmer or folder, but the faults and transitions are lost. Firmware Upgrade Procedure CPU35x, CPU36x and CPU37x operating firmware is stored in FLASH memory. Firmware upgrades are provided on CD and diskette media, and are usually available for download from the GE Fanuc Technical Support web site. Upgrades are installed by a serial download from a personal computer (PC) to the CPU. A PC running Microsoft® Windows 95 or later with one RS-232 serial port is required. Upgrades on CD or diskette media require a suitable drive on the PC. In addition, a serial cable is required. The following serial cable kit is available: IC690ACC901 Mini Converter Kit with cable (RS-232/RS-485) IC693CMM321 (EM3) Compatibility All Ethernet Interface (IC693CMM321) modules used with release 6.50 or later of any IC693 PLC should be updated to release 1.10 or later of the IC693CMM321. Ethernet-based PLC programmers require both CPU release 6.50 or later and IC693CMM321 release 1.10 or later. During a RUN-Mode Program Store of a large program block (greater than about 14 kilobytes), the IC693CMM321 may time-out, causing communications to fail. Changing the Communication Window to Run-to-Completion mode, or storing the program in Stop mode, will allow the store to take place successfully. This issue is less likely to occur in IC693CMM321-FG (version 3.00) and later versions, but is still possible. FIP Bus Controller Compatibility Version 3 or later of IC693BEM340 and IC693BEM341 FIP Bus Controller firmware is required for release 8.00 or later of IC693 PLC CPU firmware. Timeout Writing To FLASH Users of VersaPro or Control software may experience a request timeout when writing very large programs to flash. To avoid this issue, increase the request timeout setting in the Advanced section of the Edit Ports dialog, available on the Ports tab on the Communications Setup dialog. Set the Request Timeout to 25 seconds. Storing Large Configurations An IC693 PLC can support up to 20 IC693DSM314 modules. This number may be reduced by including other modules (such as APM and GBC modules) in the hardware configuration, by programmer or HMI connections that read the reference or fault tables, and by applications with unusually small amounts of free memory. If the configuration and user program are stored at the same time, the presence of either C blocks within the LD program or a C logic program may also affect the number of DSM314 modules that may be included in a system. If the Important Product Information 3 GFK-2241 store fails, it may be possible to store the hardware configuration to the PLC by first storing the logic program and then storing the configuration separately. No Model Number Checking with Logicmaster 90 programmer The No Model Number Checking feature does not support storing a 311, 313, 321, 323 or 331 configuration to a Release 9.0 or later CPU. Simultaneous Load and Store When operating with multiple programmers attached, if a programmer initiates a store operation while a load operation initiated by another programmer is already in progress, the load request will fail. Transition Tables are not cleared when the reference tables are cleared. The transition tables are not cleared upon clearing the reference tables through the programmer New Features Modbus RTU Master This release adds Modbus RTU Master to the protocols available on serial ports 1 and 2 of the IC693CPU363. PLC applications can use COMMREQ function blocks to send Modbus RTU queries and receive responses on either or both of these ports. See Modbus RTU Master Communications, GFK-2220 for details. Restrictions and Significant Open Issues Timing Issue with ALG220/221 Modules May Result in Incorrect %AI Values Read by CPU A problem was found with the IC693ALG220/221F (and earlier versions) where the actual %AI values reported by the card may exhibit erratic behavior (versions F and earlier may show this problem; the problem was fixed in version G or later). Certain current or voltage levels within the input range applied to the card could cause the %AI values to report incorrectly. The problem stems from the use of particular optocouplers, which may exhibit timing issues with these CPU35x/36x modules. (NOTE: CPUs 341, 331, 321, 313, and 311 have not exhibited this problem.) The IC693 PLC will generate a fatal fault if a ladder containing DOIO function block calls to a smart module is repeatedly placed in RUN then STOP mode A problem was found with the CPU where a ladder containing a call to a DOIO function block would cause the PLC to run out of system memory. This is caused when the PLC transitions to run mode and back to stop mode several times. If the configuration is stored, the system memory will be freed, and the PLC will resume normal operation. IC693 PLC CPU may Develop Fatal Fault During Store of Folders with Large Configurations The IC693 PLC CPU may generate a fatal fault during a store of a folder with an especially large configuration. This may be made worse by storing a program and configuration at the same time, or by having datagrams from a programmer present during the store. PID Integral Contribution The PID Integral Contribution is not calculated correctly with an integral rate of 0 or 1. Reading from an Invalid Flash Part may Cause a Watch Dog Timeout If a corrupted flash part is read, the Watch Dog Timer on the PLC may be triggered. This can be fixed by completing a valid flash store. 4 Important Product Information GFK-2241 Fatal Fault Occurs when Configuring a Module with the HHP Following a Maximum Size PLC Store The IC693 PLC CPU may generate a fatal fault while attempting to configure a module with the Hand-Held Programmer (HHP) following a maximum size store to the PLC. Firmware Update Fail Following Power-up with Clear M/T and a Write to Flash Firmware update may fail following a power-up with Clear M/T pressed on the Hand-Held Programmer and a write to flash. Cycling power on the PLC will enable the upgrade to proceed. Documentation Instructions for using this CPU can be found in the latest versions of the following manuals. These manuals are available at http://www.gefanuc.com/support/plc/s9030.htm in the Manuals section. IC693 Installation and Hardware Manual, GFK-0356 IC693 PLC System Manual, GFK-1411 IC693 PLC CPU Instruction Set Reference Manual, GFK-0467 Modbus RTU Master Communications, GFK-2220 Serial Communications User’s Manual, GFK-0582 Important Product Information 5 GFK-2241 IC693CPU363 Data CPU Type Single slot CPU module Total Baseplates per System 8 (CPU baseplate + 7 expansion and/or remote) Load Required from Power Supply 890 milliamps from +5 VDC supply Processor Speed 25 MegaHertz Processor Type 80386EX Typical Scan Rate .22 milliseconds per 1K of logic (Boolean contacts) User Memory (total) 240K (245,760) Bytes. Note: Actual size of available user program memory depends on the amounts configured for the %R, %AI, and %AQ configurable word memory types (described below). Discrete Input Points - %I 2,048 Discrete Output Points - %Q 2,048 Discrete Global Memory - %G 1,280 bits Internal Coils - %M 4,096 bits Output (Temporary) Coils - %T 256 bits System Status References - %S 128 bits (%S, %SA, %SB, %SC - 32 bits each) Register Memory - %R Configurable in 128 word increments, from 128 to 16,384 words with DOS programmer, and from 128 to 32,640 words with Windows programmer Ver. 2.2 or later, or VersaPro version 1.0 or later. Analog Inputs - %AI Configurable in 128 word increments, from 128 to 8,192 words with DOS programmer, and from 128 to 32,640 words with Windows programmer Ver 2.2 or later, or VersaPro version 1.0 or later. Analog Outputs - %AQ Configurable in 128 word increments, from 128 to 8,192 words with DOS programmer, and from 128 to 32,640 words with Windows programmer Ver. 2.2 or later, or VersaPro version 1.0 or later. System Registers (for reference table viewing only; cannot be referenced in user logic program) 28 words (%SR) Timers/Counters >2,000 (depends on available user memory) Shift Registers Yes Built-in Serial Ports 3 (one uses connector on PLC power supply). Supports SNP/SNPX slave (on all three ports) and RTU slave and Serial I/O (on Ports 1 and 2). Requires CMM module for CCM and PCM module for RTU master. Communications LAN – Supports multidrop. Also supports Ethernet, FIP, Profibus, GBC, GCM, and GCM+ option modules. Override Yes Battery Backed Clock Yes Interrupt Support Supports the periodic subroutine feature. Type of Memory Storage RAM and Flash PCM/CCM Compatibility Yes Floating Point Math Support Yes, firmware-based

Warning: include_once(/js/tracking.php): failed to open stream: No such file or directory in /var/www/series/revision.php on line 248 Warning: include_once(): Failed opening '/js/tracking.php' for inclusion (include_path='.:/usr/share/php:/usr/share/pear') in /var/www/series/revision.php on line 248