IC693CPU313 | IC693CPU313J

GE-IP | 9030 | GE Fanuc 90-30 GE-IP PLC

product-image

IC693CPU313 | IC693CPU313J

  • Availability: In StockShips Today!
  • Units in Stock: Immediate Availablity: 4 Units!
  • Call for best Pricing+ 1 919 680 1773
  • Manufacturer: GE-IP
  • Description: GE Fanuc Series 90-30 5 Slot Rack with Turbo CPU in base 1k Registers
  • Weight: 1 lbs :: ≈ 1 kgs
  • Warranty: 1 Years
  • Product Revisions Available:
  • Other Available Revisions of the IC693CPU313 : A, B, C, D, E, F, G, H, I, J, K, L, M, N, O, P, Q, R, S, T, U, V, W, X, Y, Z, -AA, -AB, -AC, -AE,

Product Manual Excerpt

Configuration Using the LM90 Configurator With the I/O Processor Module installed in its proper rack/slot location, the LM90 configurator software program can be used to configure the I/O Processor module in the off-line mode. Once the complete set of configuration data has been entered, it must then be downloaded to the PLC (in the on-line mode) to become effective in the I/O Processor. The I/O Processor module configuration is done by completing setup screens in the Logicmaster 90-30 configuration software like any other Series 90-30 module. The setup screens that are used for this module are shown and described below. Configuration Screen 1, ABS Encoder Function Catalog #: IO PROCESSOR MODULE SLOT IOP Ref Adr : %I00001 Ref Adr : %Q00001 Ref Adr : %AI0001 Ref Adr : %AQ0001 Function : ABS–256 Encoder Dir: NORMAL Posn Offset: 0 Inp Thresh : NON–TTL Strobe1 Edg: POS InTmr1 Mode: IN10 InTmr2 Mode: IN12 Timebase ms: 1000 Output 5 : DISABLED Output 6 : DISABLED Output 7 : DISABLED Output 8 : DISABLED Out Default : NORMAL Strobe2 Edg: POS Strobe3 Edg: POS Strobe4 Edg: POS Strobe1 Enb: ALWAYS Strobe2 Enb: ALWAYS Strobe3 Enb: ALWAYS Strobe4 Enb: ALWAYS Figure 3-1. IOP Configuration Screen 1 (Function = ABS Encoder) These entries allow you to define the starting address for each type of I/O data transferred between the PLC and this I/O Processor module during each PLC sweep. Starting addresses must be unique for each module and address overlaps are not allowed by the Configurator. Toggle this entry field to select the type of inputs to be applied to the module. Note This parameter must be set correctly before any of the following parameters are set. Changing this selection causes all others to be set to the default values for the new function. The choices are: Ref Adr Function 3 3-11 GFK-1028 Chapter 3 Configuration ABS-256 ( default ) Encoder 8-bit parallel gray code input (for 0–255 counts) ABS-360 Encoder 9-bit parallel excess 76 gray code (for 0–359 count rollover) ABS-512 Encoder 9-bit parallel gray code (for 0–511 counts) (Note that when ABS-360 or 512 is selected, Input 9 is not available for a strobe Input and faceplate Output 5 is unavailable.) ABS-1024 Encoder 10-bit parallel gray code for 0–1023 counts. (Note that when ABS-1024 is selected, Inputs 9 and 10 are not available for strobe Inputs and faceplate Outputs 5 and 6 are unavailable.) AQUADB Encoder AQUADB input selection (Note that when AQUADB is selected, the remaining selections in this column change. See the next screen for these descriptions.) This parameter allows you to change the count direction (UP or DOWN) without reversing the Absolute Encoder direction of rotation. If the NORM (default) is selected, increasing the count input causes the IOP to register UP counts and decreasing the count input causes the IOP to register DOWN counts. The REV selection produces the opposite effect. Default: NORMAL This parameter allows you to adjust the count input with an offset value to compensate for a rotational offset error in the Encoder coupling. Enter any required count value within the count range. Default: 0 Selects the Input voltage level to be used. If 5 VDC inputs are used, select TTL, otherwise select NON-TTL (for 10–30 VDC inputs). Default: NON-TTL This parameter selects the inputs that control the starting and stopping of Timer 1. The resulting time recorded for Timer 1 is reported in the eleventh %AI word. The selection IN10 causes Timer 1 to report the elapsed time (in milliseconds) from the configured edge of input 10 to the other edge of input 10. The selection IN09-10 causes Timer 1 to report the elapsed time (in milliseconds) from the configured edge of input 10 to the configured edge of input 9. Default: IN10 This parameter selects the inputs that control the starting and stopping of Timer 2. The resulting time recorded for Timer 2 is reported in the twelfth %AI word. The selection IN12 causes Timer 2 to report the elapsed time (in milliseconds) from the configured edge of input 12 to the other edge of input 12. The selection IN11-12 causes Timer 2 to report the elapsed time (in milliseconds) from the configured edge of input 12 to the configured edge of input 11. Default: IN12 This parameter allows you to enter the time base that is used to determine the Counts per Timebase return data (second %AI word). The default is 1000 milliseconds (1 second) resulting in Counts per Timebase return data that indicates input counts per second. Default: 1000 This parameter allows you to select whether Terminal point 9 is to be used for an output or an input. DISABLED defines the point as Input #9 while ENABLED selects it for use as output #5. Default: DISABLED This parameter allows you to select whether Terminal point 10 is to be used for an output or an input. DISABLED defines the point as Input #10 while ENABLED selects it for use as output #6. Default: DISABLED Encoder Dir Posn Offset Inp Thresh InTmr1 Mode InTmr2 Mode Timebase ms Output 5 Output 6 3 3-12 GFK-1028 Series 90-30 I/O Processor User’s Manual - June 1994 This parameter allows you to select whether Terminal point 11 is to be used for an output or an input. DISABLED defines the point as Input 11 while ENABLED selects it for use as output #7. Default: DISABLED This parameter allows you to select whether Terminal point 12 is to be used for an output or an input. DISABLED defines the point as Input #12 while ENABLED selects it for use as output #8. Default: DISABLED

Warning: include_once(/js/tracking.php): failed to open stream: No such file or directory in /var/www/series/revision.php on line 248 Warning: include_once(): Failed opening '/js/tracking.php' for inclusion (include_path='.:/usr/share/php:/usr/share/pear') in /var/www/series/revision.php on line 248