IC693CPU311 | IC693CPU311-AD

GE-IP | 9030 | GE Fanuc 90-30 GE-IP PLC

product-image

IC693CPU311 | IC693CPU311-AD

  • Availability: In StockShips Today!
  • Units in Stock: Immediate Availablity: 7 Units!
  • Call for best Pricing+ 1 919 680 1773
  • Manufacturer: GE-IP
  • Description: GE Fanuc Series 90-30 5-Slot Rack With CPU in base
  • Weight: 1 lbs :: ≈ 1 kgs
  • Warranty: 1 Years
  • Product Revisions Available:
  • Other Available Revisions of the IC693CPU311 : A, B, C, D, E, F, G, H, I, J, K, L, M, N, O, P, Q, R, S, T, U, V, W, X, Y, Z, -AA, -AB, -AC, -AD, -AE,

Product Manual Excerpt

Operational Notes If Upgrading Firmware The user program, configuration, CPU ID (used for SNP communication), and status tables will automatically be cleared when the CPU firmware EPROM is changed. So you will need to restore these after performing a firmware upgrade. The user program, configuration, and status tables can be restored from a program folder, from memory card, or EEPROM. The SNP ID must be set separately using the MS-DOS PLC programming software, VersaPro software, or the Hand-Held Programmer. EM3 Compatibility All IC693 Ethernet Interface (IC693CMM321) modules used with release 6.50 or later of the IC693 PLC should be updated to release 1.10 or later of the IC693CMM321. The MS-DOS PLC programming software (IC693 TCP/IP/Ethernet) requires both CPU release 6.50 or later and IC693CMM321 release 1.10 or later. During a Run Mode (alt-s) Program Store of a large program block (greater than 14 kilobytes), the EM3 may time-out, causing communications to fail. Changing the Communication Window to Run-to-Completion mode, or storing the program in stop mode, will allow the store to take place successfully. FBC Compatibility The FBC version 3 or later is required for release 8.00 or later of the IC693 PLC CPU firmware. Problems Resolved by This Firmware Release (8.40) Time-of Day (TOD) Clock Start-up Problem on CPU331 and CPU341 In some cases, if the backup battery was disconnected after the CPU was powered down, the TOD clock would not restart when the PLC was powered back up. This would result in a fatal fault being logged that identified the failure of the TOD clock. Subsequent cycling of power would not cause the clock to restart. It could be restarted, however, by removing the CPU and shorting the “super capacitor” memory backup capacitor. This problem has been corrected in firmware release 8.40. (Note that CPUs 311, 313, and 323 do not have a TOD clock.) Users with earlier versions of CPU331 or CPU341 who experience this problem are advised to upgrade these CPUs to firmware release 8.40 (see the heading “Firmware Upgrade Kits”). Problems Resolved by Prior Firmware Release 8.21 FBC Editing with Hand Held Programmer (HHP) A soft alarm fault could occur in release 8.20 when editing an FBC configuration with a hand held programmer. This problem has been corrected in release 8.21. Storing Foreign Module Configuration to Slot 1 Storing a configuration with a foreign module in slot 1 (possible only on 311, 313, or 323) would result in a fatal fault in release 8.20. This has been corrected in release 8.21.

Warning: include_once(/js/tracking.php): failed to open stream: No such file or directory in /var/www/series/revision.php on line 248 Warning: include_once(): Failed opening '/js/tracking.php' for inclusion (include_path='.:/usr/share/php:/usr/share/pear') in /var/www/series/revision.php on line 248