IC693CMM302 | IC693CMM302O

GE-IP | 9030 | GE Fanuc 90-30 GE-IP PLC

product-image

IC693CMM302 | IC693CMM302O

  • Availability: In StockShips Today!
  • Units in Stock: Immediate Availablity: 7 Units!
  • Call for best Pricing+ 1 919 680 1773
  • Manufacturer: GE-IP
  • Description: GE Fanuc Series 90-30 Communication card Genius 1 Kbyte
  • Weight: 1 lbs :: ≈ 1 kgs
  • Warranty: 1 Years
  • Product Revisions Available:
  • Other Available Revisions of the IC693CMM302 : A, B, C, D, E, F, G, H, I, J, K, L, M, N, O, P, Q, R, S, T, U, V, W, X, Y, Z,

Product Manual Excerpt

This release consists of hardware change s for improved manufacturability . Features, performance and compatibility are no t affected. Compatibility Specific equipment or software versions required for compatibility with the Enhanced Communications Module are listed below. CPU : For rel. 4.4 or later of the CPU firmware (CPU versions IC693CPU311L, - 321L, - 331M, - 313D, - 323D or later) the number of GCM+’s that can be configured is limited only by the maximum configuration size the PLC can hold. For prior releases of the CPU firmware beginning at 3.51 (CPU versions IC693CPU311K, - 321K, - 331L, IC693CPU313 to version C and - 323, to version D) a maximum of two Enhanced Communications Modules can be installed in the same PLC. GCM: The Enhanced Communications Module cannot be installed in the same PLC as Communications Module IC693CMM301. Programming software : rel. 3.5 (IC641SWP301L, - 3 04J, - 306F, - 307F, - 326F) or later is required. Operating Notes Bus Termination: This module operates only on a properly - terminated Genius bus. If the module will be powered up before installation on a properly - terminated bus, connect a 75 - ohm resistor acr oss its Serial 1 and Serial 2 terminals to assure proper powerup. Product Documentation Series 90 - 30 Installation and Hardware Manual, GFK - 0356 Series 90 - 30/20/Micro CPU Instruction Set Reference Manual, GFK - 0467 Series 90 - 30 Enhanced Genius Communications Module User's Manual, GFK - 0695 General Installation Requirements This product is intended for use with the 9030 or RX3i system. Its components are considered open equipment [having live electrical parts that may be accessible to users] and must be insta lled in an ultimate enclosure that is manufactured to provide safety. As a minimum, the enclosure shall provide a degree of protection against solid objects up to 12mm (e.g. fingers). This equates to a NEMA/UL Type 1 enclosure or an IP20 rating (IEC60529) providing at least a pollution degree 2 environment. * indicates a trademark of GE Intelligent Platforms, Inc. and/or its affiliates. All other trademarks are the property of thei r respective owners. All rights reserved. 2 Important Product Informa tion GFK - 1485 C Installation in Hazardous Areas The system containing the module must be mounted within an ultimate enclosure that can be accessed only by the use of a tool. The following information is for pr oducts bearing the UL marking for Hazardous Locations or ATEX marking for explosive atmospheres:  EQUIPMENT LABELED WITH REFERENCE TO CLASS I, GROUPS A, B, C & D, DIV. 2 OR ZONE 2 HAZARDOUS AREAS IS SUITABLE FOR USE IN CLASS I, DIVISION 2, GROUPS A, B, C, D , ZONE 2 OR NON - HAZARDOUS AREAS ONLY  WARNING – EXPLOSION HAZARD – SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I, DIVISION 2 OR ZONE 2;  WARNING – EXPLOSION HAZARD – WHEN IN HAZARDOUS AREAS, TURN OFF POWER BEFORE REPLACING OR WIRING MODULES; AND  WARNING – EXPLOSION HAZARD – DO NOT CONNECT OR DISCONNECT EQUIPMENT UNLESS POWER HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NONHAZARDOUS.

Warning: include_once(/js/tracking.php): failed to open stream: No such file or directory in /var/www/series/revision.php on line 248 Warning: include_once(): Failed opening '/js/tracking.php' for inclusion (include_path='.:/usr/share/php:/usr/share/pear') in /var/www/series/revision.php on line 248