IC693ADC311 | IC693ADC311F

GE-IP | 9030 | GE Fanuc 90-30 GE-IP PLC

product-image

IC693ADC311 | IC693ADC311F

  • Availability: Out of Stock
  • Units in Stock: Notice: Undefined variable: showInv in /var/www/series/revision.php on line 143
  • Call for best Pricing+ 1 919 680 1773
  • Manufacturer: GE-IP
  • Description: Series 9030 CIMPLICITY
  • Weight: 1 lbs :: ≈ 1 kgs
  • Warranty: 1 Years
  • Product Revisions Available:
  • Other Available Revisions of the IC693ADC311 : A, B, C, D, E, F, G, H, I, J, K, L, M, N, O, P, Q, R, S, T, U, V, W, X, Y, Z,

Product Manual Excerpt

Important Product Information 5 GFK-1126X Changes to Documentation The IC69* PLC Serial Communications User’s Manual will be updated to describe the Generic Output and pager enunciation feature in its next revision (rev D). These features are supported by the CPU351, CPU352, and CPU363 CPUs’ embedded serial ports. Sending a COMM_REQ to the CPU351, CPU352, or CPU363 serial ports. When sending a Communications Request (C OMM_REQ) to the CPU351, CPU352, or CPU363 serial ports, the SYSID of the COMM_REQ must be 1 and the TASK ID must be 19 decimal for port 1 or 20 decimal for port 2. RTU With the above exception about the SYSID and TASK ID fields, using RTU on the CPU351, CPU352, or CPU363 serial ports is the same as using RTU on a CCM, which is described in the IC69* PLC Serial Communications User’s Manual. Generic Output Generic Output is selected for Port 1 or Port 2 of the CPU351, CPU352, or CPU363 CPUs by choosing “CUSTOM” as the mode for the port in the CPU Configuration and storing this to the PLC. Generic Output is accomplished by using the put string COMM_REQ. Using the autodial COMM_REQ with the put string COMM_REQ accomplishes the pager enunciation feature as described below. Using Pager Enunciation and Generic Output This feature allows the CPU351, CPU352, and CPU363 CPUs to automatically dial a pager via modem and send a specified byte string from Serial Port 1 or 2. Pager dialing and message transmission are set up by COMM_REQ functions in the ladder logic. Note To implement this feature, Serial Port 2 must be configured as a CUSTOM port as mentioned above in the “Generic Output” item. Pager enunciation is implemented by three commands, requiring three COMM_REQ command blocks: Autodial : 04400 (1130H) -Dials the modem. This command works the same way that the SNP Master Autodial command 7400 does. Put string : 04401 (1131H) - Specifies an ASCII string, from 1 to 250 bytes in length, to send from the serial port. Autodial : 04400 (1130H) - It is the responsibility of the PLC application program to hang up the phone connection. This is accomplished by reissuing the autodial command and sending the hang-up command string. 6 Important Product Information GFK-1126X Autodial Command Block The Autodial command automatically transmits an Escape sequence that follows the Hayes convention. If you are using a modem that does not support the Hayes convention, you may be able to use the Put String command to dial the modem. Examples of commonly used command strings for Hayes-compatible modems are listed below: Command String Length Function ATDP15035559999 16 (10H) Pulse dial the number 1-503-555-9999 ATDT15035559999 16 (10H) Tone dial the number 1-503-555-9999 ATDT9,15035559999 18 (10H) Tone dial using outside line with pause ATH0 5 (05H) Hang up the phone ATZ 4 (04H) Restore modem configuration to internally saved values Table 6-1 lists a sample COMM_REQ command block that dials the number 234-5678 using a Hayes-comp atible modem. Table 6-1. Sample Command Block for CUSTOM Protocol Autodial Command Word Definition Values 1 0009H CUSTOM data block length (includes command string) 2 0000H NOWAIT mode 3 0008H Status word memory type (%R) 4 0000H Status word address minus 1 (Register 1) 5 0000H not used 6 0000H not used 7 04400 command (1130H) Autodial command number 8 00030 (0001H) Modem response timeout (30 seconds) 9 0012 (000CH) Number of bytes in command string 10 5441H A (41H), T (54H) 11 5444H D (44H), T (54H) 12 3332H Phone number: 2 (32H), 3 (33H) 13 3534H 4 (34H), 5 (35H) 14 3736H 6 (36H), 7 (37H) 15 0D38H 8 (38H) (0DH) Important Product Information 7 GFK-1126X Put String Command Block Table 6-2 lists a sample COMM_REQ command block that sends the data string, “hello world” using the Put String command (04401). A maximum transmit timeout of 30 seconds is specified. The string data begins at Word 10. This command is similar to the Autodial command except that Put String does not send the escape sequence for Hayes- compatible modems. The Maximum Transmit Timeout field specifies, in seconds, the maximum time interval the COMM_REQ will wait for the entire string to be sent. If this time is set to 0, a default value of 4 seconds plus the time required to transmit the number of characters is used. If the string is not transmitted during the specified interval or the default interval, an error code is generated. The Number of Bytes in Command String field specifies the length of the command string to be sent. This length includes all characters. A status code indicating successful transmission will be returned when the string has been completely sent out the serial port. Table 6-2. Sample Command Block for Put String Command Word Definition Values 1 0009H CUSTOM data block length (includes command string) 2 0000H NOWAIT mode 3 0008H Status word memory type (%R) 4 0000H Status word address minus 1 (Register 1) 5 0000H not used 6 0000H not used 7 04401 command (1131H) Put String command number 8 001EH Maximum transmit timeout (30 seconds) 9 000BH Number of bytes in command string 10 6568H h (68H), e (65H) 11 6C6CH l (6CH), l (6CH) 12 206FH o (6F), “ “ (20H) 13 6F77H w (77H), o (6FH) 14 6C72H r (72H), l (6CH) 15 0064H d (64H) 8 Important Product Information GFK-1126X Status Word for Custom Protocol COMM_REQs A value of 1 will be returned in the C OMM_REQ status word upon successful completion of a CUSTOM protocol command. Any other value returned in the COMM_REQ status word is an error code where the low byte is a major error code and the high byte is a minor error code. Table 6-3. Status Codes for Custom Protocol Major Status Code Description 1 (01H) Successful Completion (this is the expected completion value in the COMM_REQ status word). 12 (0CH) Local CSTM_PROT error — Port configuration command 65520 (FFF0H). An error occurred while processing a local command. The minor error code identifies the specific error. 2 (02H) COMM_REQ command is not supported. 13 (0DH) Remote CSTM_PROT error — Put String command 4401 (1131H). An error occurred while processing a remote command. The minor error code identifies the specific error. 2 (02H) String length exceeds end of reference memory type. 3 (03H) COMM_REQ data block length is too small. String data is missing or incomplete. 48 (30H) Serial output timeout. The serial port was unable to transmit the string. (Could be due to missing CTS signal when the serial port is configured to use hardware flow control.) 50 (32h) COMM_REQ timeout. The COMM_REQ did not complete within a 20-second time limit. 14 (0EH) Autodial Error — Autodial command 4400 (1130). An error occurred while attempting to send a command string to an attached external modem. The minor error code identifies the specific error. 1 (01H) Not used. 2 (02H) The modem command string length exceeds end of reference memory type. 3 (03H) COMM_REQ Data Block Length is too small. Output command string data is missing or incomplete. 4 (04H) Serial output timeout. The serial port was unable to transmit the modem autodial output. (May be due to missing CTS signal when the serial port is configured to use hardware flow control.) 5 (05H) Response was not received from modem. Check modem and cable. 6 (06H) Modem responded with BUSY. Modem is unable to complete the requested connection. The remote modem is already in use; retry the connection request at a later time. 7 (07H) Modem responded with NO CARRIER. Modem is unable to complete the requested connection. Check the local and remote modems and the telephone line. 8 (08H) Modem responded with NO DIALTONE. Modem is unable to complete the requested connection. Check the modem connections and the telephone line. 9 (09H) Modem responded with ERROR. Modem is unable to complete the requested command. Check the modem command string and modem. 10 (0AH) Modem responded with RING, indicating that the modem is being called by another modem. Modem is unable to complete the requested command. Retry the modem command at a later time. 11 (0BH) An unknown response was received from the modem. Modem is unable to complete the requested command. Check the modem command string and modem. The modem response is expected to be either CONNECT or OK. 50 (32H) COMM_REQ timeout. The COMM_REQ did not complete within a 20-second time limit. Documentation Instructions for using these three modules can be found in the latest version of the following manuals: General Configuration Instructions: IC693 PLC Programming Software User’s Manual Ladder Logic Programming: IC693 PLC Reference Manual Serial Communications: IC69* PLC Serial Communications User’s Manual, Rev. D Important Product Information 9 GFK-1126X IC693CPU351-GR and IC693CPU352-DG Data CPU Type Single slot CPU module Total Baseplates per System 8 (CPU baseplate + 7 expansion and/or remote) Load Required from Power Supply 890 milliamps from +5 VDC supply Processor Speed 25 MegaHertz Processor Type 80386EX Typical Scan Rate .22 milliseconds per 1K of logic (Boolean contacts) User Memory (total) 240K (245,760) Bytes. Note: Actual size of available user program memory depends on the amounts configured for the %R, %AI, and %AQ configurable word memory types (described below). Discrete Input Points - %I 2,048 Discrete Output Points - %Q 2,048 Discrete Global Memory - %G 1,280 bits Internal Coils - %M 4,096 bits Output (Temporary) Coils - %T 256 bits System Status References - %S 128 bits (%S, %SA, %SB, %SC - 32 bits each) Register Memory - %R Configurable in 128 word increments, from 128 to 16,384 words with DOS programmer, and from 128 to 32,640 words with Windows programmer Ver. 2.2 when available. Analog Inputs - %AI Configurable in 128 word increments, from 128 to 8,192 words with DOS programmer, and from 128 to 32,640 words with Windows programmer Ver 2.2 when available. Analog Outputs - %AQ Configurable in 128 word increments, from 128 to 8,192 words with DOS programmer, and from 128 to 32,640 words with Windows programmer Ver. 2.2 when available. System Registers ( for reference table viewing only; cannot be referenced in user logic program) 28 words (%SR) Timers/Counters >2,000 (depends on available user memory) Shift Registers Yes Built-in Serial Ports 3 (one uses connector on PLC power supply). Supports SNP, SNPX (on all three ports) and RTU (on Ports 1 and 2). Requires CMM module for CCM. Communications LAN – Supports multidrop. Also supports Ethernet, FIP, Profibus, GBC, GCM, and GCM+ option modules. Override Yes Battery Backed Clock Yes Interrupt Support Supports the periodic subroutine feature. Type of Memory Storage RAM and Flash PCM/CCM Compatibility Yes Floating Point Math Support CPU351: Firmware-based CPU352: Hardware-ba

Warning: include_once(/js/tracking.php): failed to open stream: No such file or directory in /var/www/series/revision.php on line 248 Warning: include_once(): Failed opening '/js/tracking.php' for inclusion (include_path='.:/usr/share/php:/usr/share/pear') in /var/www/series/revision.php on line 248